-
Steel Nut Bolts
-
Steel Hex Bolt
-
Carbon Steel Bolt
-
High Tensile Stainless Steel Bolts
-
Carbon Steel Nuts
-
Stainless Steel Nut
-
Steel Flat Washer
-
Spring Steel Washers
-
Stainless Steel Washer
-
Fully Threaded Studs
-
Non Standard Fasteners
-
Seismic Wedge Anchors
-
Self Tapping Screw
-
Electrical Fasteners
-
Solar Panel Fasteners
-
Stainless Steel Shackle
-
BOSSARDThis is our European partner
-
LiIt's a good business
A354 ANSI Carbon Steel HDG Fully Threaded Studs

Contact me for free samples and coupons.
Whatsapp:0086 18588475571
Wechat: 0086 18588475571
Skype: sales10@aixton.com
If you have any concern, we provide 24-hour online help.
xMaterial | Carbon Steel | SIZE | 1/4-4INCH |
---|---|---|---|
LENGTH | ALL KIND OF LENGTH | Surface | HDG YZP ZP BLACK |
Samples | Free | ||
High Light | A354 Fully Threaded Studs,HDG Fully Threaded Studs,ANSI 1 Inch All Thread Rod |
A354 ANSI Carbon Steel HDG 1 Inch All Thread Rod
ASTM A354 covers the chemical and mechanical requirements of quenched and tempered alloy steel bolts, studs, and other externally threaded fasteners 4” and under in diameter. Two strength levels, grades BC and BD are summarized below. This specification is unrestricted in its configuration and can be a headed bolt, bent bolt, or threaded rod.
|
|||||||||||||
|
|
|||||||||||||
|
A354 Grades
BD | Grade BD bolts are higher in strength than grade BC, and equal in strength to ASTM F3125 grade A490 bolts. Unlike A490 however, the A354 standard is unrestricted in its configuration. Also, since A490 bolts are for structural use and do not exceed 1-1/2” in diameter, A354 grade BD should be considered for anchor bolts, threaded rods, other styles of headed bolts, and bolts larger than 1-1/2” diameter where similar mechanical properties are desired. A354 grade BD does not require a magnetic particle test like A490, except when called out as a supplemental requirement. |
---|---|
BC | Lower in strength than BD. Should be considered in lieu of F3125 grade A325 bolts when configuration and size conflicts occur with A325 as described above for grade BD and A490 bolts./td> |
A354 Mechanical Properties
Grade | Size | Tensile, ksi, min | Yield, ksi, min | Elong %, min | RA %, min | Hardness, HRC |
---|---|---|---|---|---|---|
BC | 1/4 - 2-1/2 | 125 min | 109 | 16 | 50 | 26 - 36 |
Over 2-1/2 | 115 min | 99 | 16 | 45 | 22 - 33 | |
BD | All Sizes | 150 - 173 | 130 | 14 | 40 | 33 - 38 |
A354 Chemical Properties
Element | All sizes of Grade BC, Grade BD through 2-1/4” diameter. | Grade BD over 2-1/4” |
---|---|---|
Carbon, % | 0.30 to 0.53 | 0.35 to 0.53 |
Manganese, % min | 0.60 | 0.60 |
Phosphorus, % max | 0.035 | 0.035 |
Sulfur, % max | 0.040 | 0.040 |
Boron, % max | 0.003 | 0.003 |
Nickel, % min | 0.40 | |
Chromium, % min | 0.40 | |
Molybdenum, % min | 0.15 | |
Other Alloying Elements | * | * |
*steel is considered to be alloy when the maximum range given for manganese exceeds 1.65 % or a definite minimum quantity for any of the following elements is specified or required within the limits of the recognized field of constructional alloy steels: chromium, molybdenum, nickel, or any other alloying element added to obtain a desired alloying effect. |
Additional Requirements, Grade BD, Diameters above 2-1/4”
Charpy Impact | 20ft-lbs minimum @ -4F |
---|---|
Cross Sectional Hardness | Equidistant hardness readings shall be taken across the diameter of the fastener through the threaded section. Reading shall be no further apart than ¼”. No reading shall be outside the acceptable range given above, and no reading shall be greater than +/- 3 HRC points from the average mid-radius hardness value. |
A354 Recommended Hardware
Grade | Finish | Nut | Washer |
---|---|---|---|
BC | Plain | A563C Heavy Hex | F436 |
Galvanized | A563DH Heavy Hex | F436 | |
BD | All Finished | A563DH Heavy Hex | F436 |
* Nuts of other grades and styles having specified proof load stresses greater than the specified grade and style of nut are acceptable. |
Specification
A threaded rod, also known as a stud, is a relatively long rod that is threaded on both ends; the thread may extend along the complete length of the rod. They are designed to be used in tension. Threaded rod in bar stock form is often called all-thread.
All thread rod, commonly referred to as fully threaded rod, redi-rod, continuously threaded rod, TFL rod, and abbreviated ATR is used for general purpose fastening for anything from an anchor bolt to a through bolt. A variety of grades and materials are available.
Materials and Chemical compstition
1008
CHEMICAL COMPOSI % | ||||||||
C | Si | Mn | P | S | Cr | Ni | Cu | Al |
0.06 | 0.06 | 0.33 | 0.013 | 0.003 | 0.01 | 0 | 0.01 | 0.028 |
1035
CHEMICAL COMPOSI % | |||||||
C | Si | Mn | P | S | Cr | Ni | Cu |
0.34 | 0.13 | 0.73 | 0.012 | 0.002 | 0.02 | 0.01 | 0.02 |
10B21
CHEMICAL COMPOSI % | ||||||
C | Si | Mn | P | S | Cr | B |
0.2 | 0.04 | 0.81 | 0.017 | 0.007 | 0.017 | 0.0021 |
1045
CHEMICAL COMPOSI % | |||||||
C | Si | Mn | P | S | Cr | Ni | Cu |
0.45 | 0.23 | 0.58 | 0.014 | 0.006 | 0.057 | 0.008 | 0.016 |
40CR
CHEMICAL COMPOSI % | |||||||
C | Si | Mn | P | S | Cr | Ni | Cu |
0.4 | 0.21 | 0.54 | 0.015 | 0.008 | 0.95 | 0.02 | 0.02 |
35CRMO
CHEMICAL COMPOSI % | ||||||||
C | Si | Mn | P | S | Cr | Ni | Cu | Mo |
0.35 | 0.22 | 0.59 | 0.01 | 0.003 | 0.93 | 0.01 | 0.01 | 0.21 |
42CRMO
CHEMICAL COMPOSI % | ||||||||
C | Si | Mn | P | S | Cr | Ni | Cu | Mo |
0.42 | 0.27 | 0.92 | 0.013 | 0.004 | 1.01 | 0.03 | 0.04 | 0.2 |
Finish
PLAIN ZP YZP BLACK HDG DACROMET GEOMET CHROME NICKEL AND SO ON
PACKING
QBH BULK
20-25KG/CTN,36CTNS/PALLET
20-30KG/BAGS,36BAGS/PALLET
ONE TON/BOXES
50KG/ IRON DRUM,12 IRON DRUMS/PALLET
QBH SMALL PACKING
Packing in small boxes according to customer’s requirements
Packing in plastic bag according to customer’s requirements
QBH PALLET TYPE
SOLID WOOD FUMIGATION PALLET
EURO Pallet
THREE SPLINT PALLET
WOODEN BOX
The advantages of QBH
- QBH brand sales to the main quality assurance.
- Years of export trade management, excellent service, word-of-mouth guarantee.
- By working with TUV,escort for quality.
- Customization of non-standard parts can be made according to customer's requirements and drawings.
- For quality customers,we can provide a certain credit period.