-
Steel Nut Bolts
-
Steel Hex Bolt
-
Carbon Steel Bolt
-
High Tensile Stainless Steel Bolts
-
Carbon Steel Nuts
-
Stainless Steel Nut
-
Steel Flat Washer
-
Spring Steel Washers
-
Stainless Steel Washer
-
Fully Threaded Studs
-
Non Standard Fasteners
-
Seismic Wedge Anchors
-
Countersunk Head Screws
-
Electrical Fasteners
-
Solar Panel Fasteners
-
BOSSARDThis is our European partner
-
LiIt's a good business
Carbon Steel ASTM A307 Threaded Rod
Material | Carbon Steel Stainless Steel Brass | SIZE | 1/4-4INCH |
---|---|---|---|
LENGTH | ALL KIND OF LENGTH | Surface | HDG YZP ZP BLACK |
Samples | Free | ||
High Light | Carbon Steel ASTM A307 Threaded Rod,ASTM A307 Threaded Rod,A307 12mm Stainless Steel Threaded Rod |
4inch ANSI Carbon Steel ASTM A307 Threaded Rod
Specification
The ASTM A307 specification covers carbon steel bolts and studs ranging from 1/4″ through 4″ diameter. This is your everyday, run of the mill bolt specification often manufactured using A36 round bar. There are three grades A, B, and C* which denote tensile strength, configuration, and application. Refer to the Mechanical Properties Chart for the subtle strength differences within each grade.
A threaded rod, also known as a stud, is a relatively long rod that is threaded on both ends; the thread may extend along the complete length of the rod. They are designed to be used in tension. Threaded rod in bar stock form is often called all-thread.
All thread rod, commonly referred to as fully threaded rod, redi-rod, continuously threaded rod, TFL rod, and abbreviated ATR is used for general purpose fastening for anything from an anchor bolt to a through bolt. A variety of grades and materials are available.
|
|||||||||||||
|
|
|||||||||||||
|
A307 Grades
A |
QBH 307A |
Headed bolts, threaded rods and bent bolts intended for general applications. |
---|---|---|
B |
QBH 307B |
Heavy hex bolts and studs intended for flanged joints in piping systems with cast iron flanges. |
C* |
QBH 307C |
Nonheaded anchor bolts, either bent or straight, intended for structural anchorage purposes. The end of a grade C anchor bolt intended to project from the concrete will be painted green for identification purposes. Permanent marking is a supplemental requirement. *As of August 2007, grade C has been replaced by specification F1554 grade 36. We will continue to supply grade C, if required by the project. |
A307 Mechanical Properties
Grade | Tensile, ksi | Yield, min, ksi | Elong %, min |
---|---|---|---|
A | 60 min | -- | 18 |
B | 60 - 100 | -- | 18 |
C* | 58 - 80 | 36 | 23 |
A307 Chemical Properties
Element | Grade A | Grade B |
---|---|---|
Carbon, max | 0.29% | 0.29% |
Manganese, max | 1.20% | 1.20% |
Phosphorus, max | 0.04% | 0.04% |
Sulfur, max | 0.15% | 0.05% |
A307 Recommended Hardware
Nuts | Washers | ||
---|---|---|---|
A307 Grades A & C* | A307 Grade B | ||
1/4 - 1-1/2 | 1-5/8 - 4 | 1/4 - 4 | |
A563A Hex | A563A Heavy Hex | A563A Heavy Hex | F844 |
Materials and Chemical compstition
1008
CHEMICAL COMPOSI % | ||||||||
C | Si | Mn | P | S | Cr | Ni | Cu | Al |
0.06 | 0.06 | 0.33 | 0.013 | 0.003 | 0.01 | 0 | 0.01 | 0.028 |
1035
CHEMICAL COMPOSI % | |||||||
C | Si | Mn | P | S | Cr | Ni | Cu |
0.34 | 0.13 | 0.73 | 0.012 | 0.002 | 0.02 | 0.01 | 0.02 |
10B21
CHEMICAL COMPOSI % | ||||||
C | Si | Mn | P | S | Cr | B |
0.2 | 0.04 | 0.81 | 0.017 | 0.007 | 0.017 | 0.0021 |
1045
CHEMICAL COMPOSI % | |||||||
C | Si | Mn | P | S | Cr | Ni | Cu |
0.45 | 0.23 | 0.58 | 0.014 | 0.006 | 0.057 | 0.008 | 0.016 |
40CR
CHEMICAL COMPOSI % | |||||||
C | Si | Mn | P | S | Cr | Ni | Cu |
0.4 | 0.21 | 0.54 | 0.015 | 0.008 | 0.95 | 0.02 | 0.02 |
35CRMO
CHEMICAL COMPOSI % | ||||||||
C | Si | Mn | P | S | Cr | Ni | Cu | Mo |
0.35 | 0.22 | 0.59 | 0.01 | 0.003 | 0.93 | 0.01 | 0.01 | 0.21 |
42CRMO
CHEMICAL COMPOSI % | ||||||||
C | Si | Mn | P | S | Cr | Ni | Cu | Mo |
0.42 | 0.27 | 0.92 | 0.013 | 0.004 | 1.01 | 0.03 | 0.04 | 0.2 |
stainless steel
化学成分CHEMICAL COMPOSI(% ) | ||||||||||
Type | C碳 | Si硅 | Mn锰 | P磷 | S硫 | Ni镍 | Cr铬 | Mo钼 | Cu铜 | Others |
≤ | ≤ | ≤ | ≤ | ≤ | ≥ | ≥ | ≥ | ≈ | ||
201Cu | 0.08 | 1.00 | 7.5-10 | 0.06 | 0.03 | 4.00-6.00 | 14.0-17.0 | 2.0-3.0 | ||
201 | 0.15 | 1.00 | 8.50 | 0.06 | 0.03 | 3.50-5.50 | 16.0-18.0 | N≤0.25 | ||
130M/202 | 0.15 | 1.00 | 7.5-10 | 0.06 | 0.03 | 4.00-6.00 | 17.0-19.0 | N≤0.25 | ||
202 | 0.15 | 1.00 | 7.5-10 | 0.06 | 0.03 | 4.00-6.00 | 17.0-19.0 | |||
301 | 0.15 | 1.00 | 2.00 | 0.045 | 0.03 | 5.00-8.00 | 16.0-18.0 | |||
302 | 0.15 | 1.00 | 2.00 | 0.045 | 0.03 | 8.00-10.0 | 17.0-19.0 | |||
XM7 (302HQ) |
0.08 | 1.00 | 2.00 | 0.045 | 0.03 | 8.50-10.5 | 17.0-9.00 | 3.0-4.0 | ||
303 | 0.15 | 1.00 | 2.00 | 0.20 | ≥0.15 | 8.00-10.0 | 17.0-19.0 | ≤0.60 | ||
303Cu | 0.15 | 1.00 | 3.00 | 0.20 | ≥0.15 | 8.0-10.0 | 17.0-19.0 | ≤0.60 | 1.5-3.5 | |
304 | 0.08 | 1.00 | 2.00 | 0.045 | 0.03 | 8.00-10.0 | 18.0-20.0 | |||
304H | 0.08 | 1.00 | 2.00 | 0.045 | 0.03 | 8.0-10.0 | 18.0-20.0 | |||
304HC | 0.08 | 1.00 | 2.00 | 0.045 | 0.03 | 8.00-10.0 | 17.0-19.0 | 2.0-3.0 | ||
304HCM | 0.08 | 1.00 | 2.00 | 0.045 | 0.03 | 8.0-10.0 | 17.0-19.0 | 2.5-4.0 | ||
304L | 0.03 | 1.00 | 2.00 | 0.045 | 0.03 | 9.0-13.0 | 18.0-20.0 | |||
304M | 0.06 | 1.00 | 2.00 | 0.045 | 0.03 | 8.50-10.0 | 18.0-20.0 | |||
305 | 0.12 | 1.00 | 2.00 | 0.045 | 0.03 | 10.5-13.0 | 17.0-19.0 | |||
305J1 | 0.08 | 1.00 | 2.00 | 0.045 | 0.03 | 11.0-13.5 | 16.5-19.0 | |||
309S | 0.08 | 1.00 | 2.00 | 0.045 | 0.03 | 12.0-15.0 | 22.0-14.0 | |||
310S | 0.08 | 1.50 | 2.00 | 0.045 | 0.03 | 19.0-22.0 | 24.0-26.0 | |||
314 | 0.25 | 15.-3.0 | 2.00 | 0.040 | 0.03 | 19.0--22.0 | 24.0-26.0 | |||
316 | 0.08 | 1.00 | 2.00 | 0.045 | 0.03 | 10.0-14.0 | 16.0-18.0 | 2.0-3.0 | ||
316Cu | 0.03 | 1.00 | 2.00 | 0.045 | 0.03 | 10.0-14.0 | 16.0-18.0 | 2.0-3.0 | 2.0-3.0 | |
316L (12Ni) |
0.03 | 1.00 | 2.00 | 0.045 | 0.03 | 12.0-15.0 | 16.0-18.0 | 2.0-3.0 | ||
316L (10Ni) |
0.03 | 1.00 | 2.00 | 0.045 | 0.03 | 10.0-14.0 | 16.0-18.0 | 2.0-3.0 | ||
321 | 0.08 | 1.00 | 2.00 | 0.045 | 0.03 | 9.00-13.0 | 17.0-19.0 | Ti≤5*C% | ||
410 | 0.15 | 1.00 | 0.03 | 11.5-13.5 | ||||||
416 | 0.15 | 1.25 | ≥0.15 | 12.0-14.0 | ||||||
420 | 0.26-0.4 | 1.00 | 0.03 | 12.0-14.0 | ||||||
410L | 0.30 | 1.00 | 1.00 | 0.040 | 0.03 | 11.5-13.5 | ||||
430 | 0.12 | 0.75 | 1.00 | 0.040 | 0.03 | 16.0-18.0 | ||||
430F | 0.12 | 1.00 | 1.25 | 0.060 | 0.15 | 16.0-18.0 | ||||
631(J1) | 0.09 | 1.00 | 1.00 | 0.040 | 0.03 | 6.50-8.50 | 16.0-18.0 | AL 0.75-1.5 | ||
2520 | 0.08 | 1.00 | 2.00 | 0.035 | 0.03 | 19.0-22.0 | 24.0-26.0 | |||
410 | 0.015 | 1.00 | 1.00 | 0.04 | 0.03 | 11.5-13.5 |
Finish
PLAIN ZP YZP BLACK HDG DACROMET GEOMET CHROME NICKEL AND SO ON
PACKING
QBH BULK
20-25KG/CTN,36CTNS/PALLET
20-30KG/BAGS,36BAGS/PALLET
ONE TON/BOXES
50KG/ IRON DRUM,12 IRON DRUMS/PALLET
QBH SMALL PACKING
Packing in small boxes according to customer’s requirements
Packing in plastic bag according to customer’s requirements
QBH PALLET TYPE
SOLID WOOD FUMIGATION PALLET
EURO Pallet
THREE SPLINT PALLET
WOODEN BOX
The advantages of QBH
- QBH brand sales to the main quality assurance.
- Years of export trade management, excellent service, word-of-mouth guarantee.
- By working with TUV,escort for quality.
- Customization of non-standard parts can be made according to customer's requirements and drawings.
- For quality customers,we can provide a certain credit period.